Additions:
@@====ADS NAS Drive Kit (NAS-806-EF)====@@
@@**PART II: Up and Running with openNAS**@@
Deletions:
Additions:
I have a 320 gig Maxtor ATA with 16 meg cache installed. The output of hdparm:
~ # hdparm /dev/hda
/dev/hda:
multcount = 0 (off)
IO_support = 0 (default 16-bit)
unmaskirq = 0 (off)
using_dma = 1 (on)
keepsettings = 0 (off)
readonly = 0 (off)
readahead = 8 (on)
geometry = 38913/255/63, sectors = 625142448, start = 0
~ # hdparm -Tt /dev/hda
/dev/hda:
Timing cached reads: 148 MB in 2.02 seconds = 73.27 MB/sec
Timing buffered disk reads: 36 MB in 3.05 seconds = 11.80 MB/sec
Timing cached reads: 152 MB in 2.01 seconds = 75.62 MB/sec
Timing buffered disk reads: 36 MB in 3.04 seconds = 11.84 MB/sec
http://all6250.blogspot.com/
Deletions:
http://all6250.blogspot.com/
Additions:
http://all6250.blogspot.com/
http://openwrt.org/
http://tobe.mine.nu/
http://www.uclinux.org/
http://forum.opennas.info/
http://wiki.opennas.info
ntx_libra.tgz
J1: Power pack
J2: Current supply of the non removable disk
J3: Current supply of the exhaust
J4: COM1
J5: Net socket
J6: COM2 (?)
JP1: JTAG (?)
JP2: IDE interface
SW1: In/circuit breaker
SW2: RESET tracer
LD1: Power LED
LD2: HDD-LED
LD3: Net traffic LED
In the Netronix NH-220 NAS devices the BRECIS MSP2006 MIPS32 4Km processor is blocked. Here it concerns one on 170Mhz clocked MIPS CCU. As is the case for others embedded/NAS here a MMU is missing to systems to the store management.
The CCU is accessible over a JTAG interface.
http://wiki.openwrt.org/OpenWrtDocs/Customizing/Hardware/JTAG_Cable
http://forum.opennas.info/viewtopic.php?t=188&highlight=ads
http://all6250.blogspot.com/
%%
Load Firmware extensions
To enable the Unicode and UPNP function for the device, you have to install the "ntx_libra.tgz" file to the device before any configuration.
To install the file,
1. Insert the included CD and click the "Browse" button.
Note: The Install Menu may auto run. Click "EXIT" to close it.
2. Select your CD-Rom drive. Select Firmware Extensions Gigabit SATA NAS with USB folder. Select the "ntx_libra.tgz" file and click "Open" to browse the file.
3. Click "Apply" to perform installation.
4. It takes a few seconds to perform installing, please wait upon installation.
%%
http://translate.google.com/translate?u=http%3A%2F%2Fforum.opennas.info%2Fviewtopic.php%3Ft%3D61%26highlight%3Dads&langpair=de%7Cen&hl=en&safe=off&ie=UTF-8&oe=UTF-8&prev=%2Flanguage_tools
Deletions:
xxx
Additions:
xxx
Deletions:
%%
[TELNET] CONNECT (nasdrive/192.168.1.2)
***
*** CONNECT TO 192.168.1.2:24
*** date 08-26-07
*** time 15:03:10
***
1452.14 1361.72
/etc/issue www.brecis.com 28 July 2003
Welcome to linux 2.4.20-br251 by BRECIS (Release 2.5.1)
Brecis linux incorporates changes from kernel.org, and uclinux.org as well
as locally derived features to provide a robust environment for the embedded
BRECIS mips chip. Almost any program that can run with less than 64k of
stack should work. Most all features of the linux kernel are provided.
The "c" runtime library originated at uclibc.org. One nice feature is
that the fork() system call works (although slowly) for this MMU-less chip.
For more information on the operating system please visit these sites:
http://www.uclinux.org
http://www.kernel.org
http://www.uclibc.org
On the CDROM distribution, see files:
README
CHANGES Accumulated change log.
RELEASE-NOTES Additional notes, and short FAQ.
uClinux/README Instructions for building/changing things.
[TELNET] INFO: DISCONNECTED
***
*** DISCONNECT
*** time 15:03:10
***
%%
